Snap these grommets into place to hold wire, cable, and cords in wet locations and form a seal against dust, debris, and water. Support shafts, bearings, and other moving parts that are routed through a hole. These grommets are slippery to allow parts to move freely in the hole. Install them on thin sheet-metal panels.
Assemble a connector that can handle multiple applications at once. Combine inserts that send power, signal, and data with a base and a hood. Protect screw-together M12 connectors when not in use. Protect harsh environment M12 connectors when not in use. Made with industry standard barrel-style ends, these connectors carry DC power between electronic devices and power supplies.
Power hydraulic and air-powered valves, motors, pumps, and pressure switches. Add as many circuits as you need with these terminal blocks and accessories. The spring -clamp terminals on these blocks make wire installation faster than other types of terminals. Push wire into the spring clamp for a secure connection that withstands vibration. Use with DIN 2 rail. Check pressure without permanently installing a gauge. FDA compliant for use near food, these plugs close off unused holes in equipment such as electrical enclosures to keep out debris and water.
Mount these drains at the bottom of your enclosure to let moisture drip out and keep electronics dry. Use these vents to maintain consistent pressure as temperatures fluctuate by allowing air to flow through sealed enclosures.
Safe for use around hazardous gasses and dust, these vents maintain steady pressure and prevent moisture buildup from temperature changes inside enclosures. Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends.
With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life. Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.
A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable. Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.
Tighten the screw-down clamp for superior pull-out resistance. Suitable for use in applications where cords are underwater— these grips are rated IP68 for protection from prolonged submersion. Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.
These grips are the most corrosion resistant of any of our submersible metal cord grips. Stainless steel construction offers the most corrosion-resistance of any of our multi-diameter wet-location cord grips.
These grips are nickel-plated brass for good corrosion resistance. The face of these grips is flush with the cable-entry point for a seamless appearance. Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter. Attach a cord grip to cable without removing connectors and rewiring.
These cord grips have a two-piece design to fit around cables with connectors. These breather vents withstand corrosion in damp environments. These breather vents are rated NEMA 6 to withstand periodic submersion in water. Seal out contaminants and prevent leaks— a rubber O-ring under the head prevents leaks and seals out contaminants. The nylon patch bonded to the threads of these socket head screws adds friction to keep vibration from loosening them, while their O-ring prevents leaks and seals out contaminants.
These metric screws have a silicone O-ring that prevents leaks and seals out contaminants. Made from stainless steel, they have good chemical resistance and may be mildly magnetic. To prevent unwanted removal, these metric screws have a tamper-resistant Torx drive— also known as a pin-in Torx drive— that makes them difficult to unscrew without special tools.
An O-ring under the head blocks leaks and seals out dust and dirt. Bolt down equipment in food processing or sanitary areas while sealing out contaminants. To prevent leaks and seal out contaminants, these metric screws have an O-ring under the head. With an O-ring under the head, these metric screws seal out leaks and contaminants while also preventing unwanted removal. Join two pieces of wood with these dowel pins. When glued, they expand for a tight fit. The window and body are made from a single piece of plastic, making these sights more shatter resistant than sights with a glass window.
Inject lubricant into motors, bearings, engine blocks, and all kinds of machinery. Use these fittings in tight spaces where protruding fittings won't work. Often used on earth movers, mining equipment, and other heavy machinery, these fittings have a T-shaped top that holds the dispensing tip in place so it won't pop off when adding grease.
Drive them into unthreaded holes. Drive these fittings into unthreaded holes. They're also known as hydraulic grease fittings. When the size or thread type of a fitting doesn't match an existing opening, use these adapters to make the connection.
Install these plugs into drum holes using a drum-plug wrench. Build these spark plugs into stationary gas-powered engines in your facility for reliable operation. Clear All. System of Measurement. Thread Size. Thread Type. Thread Pitch.
Drive Style. External Hex. External Square. Tamper- Resistant Torx. Drive Size. For Use With. Pipe Size. Specifications Met. CE Marked. FDA Compliant. For Pipe Material. Connection Type. Connection Style. Maximum Pressure. Body Shape. Plug Construction. View catalog pages Send Cancel. How can we improve? Pipe, Tubing, Hose, and Fittings. Plastic Pipe Fittings for Oil. Plastic Pipe Fittings for Gasoline.
Push-to-Connect Tube Fittings for Air. Compression Fittings for Steel Tubing. Yor-Lok Fittings for Steel Tubing. Solder-Connect Fittings for Copper Tubing.
Yor-Lok Fittings for Copper Tubing. Compatible with ARO-shape plugs and sockets. Beaded Hose Fittings for Coolant. Snap-In Rectangular Plugs. Shaft Grommets. Barrel-Style DC Connectors. Solenoid Valve Connectors. Pressure Test Fittings.
Threaded Hole Plugs. They have high strength and impact resistance. Connect these fittings to Schedule 40 plastic pipe— they are the industry standard for residential and commercial low-pressure plumbing and water supply applications.
They are plastic for good corrosion resistance. FDA compliant for use near food, these plugs close off unused holes in equipment such as electrical enclosures to keep out debris and water. Use these fittings in tight spaces where protruding fittings won't work. Often used on earth movers, mining equipment, and other heavy machinery, these fittings have a T-shaped top that holds the dispensing tip in place so it won't pop off when adding grease. Inject lubricant into motors, bearings, engine blocks, and all kinds of machinery.
They're also known as hydraulic grease fittings. System of Measurement. Thread Size. Thread Type. Thread Pitch. Pipe Size. Drive Style. Drive Size. For Use With.
For Pipe Material. Connection Style. Specifications Met. FDA Compliant. Maximum Pressure. Body Shape. Plug Construction. Gasket Material. View catalog pages Send Cancel. How can we improve?
How to Identify and Measure Fittings. Plastic Pipe Fittings for Gasoline. Plastic Pipe Fittings for Oil. Threaded Hole Plugs. Close off unused threaded holes. Threaded Submersible Hole Plugs. Sanitary Threaded Hole Plugs. Button-Head Grease Fittings.
Flush-Style Grease Fittings. Grease Fittings. Pipe Fitting Plugs. The quick brown fox jumped over the lazy dog.
0コメント